

Car keys · Strathroy-Caradoc
Ignition Lock Repair
A scrape sits beside the ignition slot, left by whoever tried the vehicle overnight in the driveway.
In plain words
Most ignition lock work happens where the vehicle already is, a driveway, a parking lot, a curb, rather than requiring a tow to a shop first. The locksmith brings cylinder decoders, extraction tools and repinning equipment to the vehicle, assesses the mechanism in place, and works through accessory, on and start until the barrel turns the way it should. A shop visit only becomes necessary when the fault turns out to be electronic rather than mechanical.
How the visit goesThe key slides in fine and turns without any resistance at all, and the dash lights flicker, but nothing catches. No click, no crank, just a key spinning loosely in a slot that used to grab hold of it properly.
Ignition Lock Repair
How the visit goes


Separating a worn key from a worn cylinder
A spare key, even an old one, answers a question a single key cannot. If the spare turns the ignition smoothly while the regular key struggles, the key itself is the likely problem, rounded edges no longer lifting the internal wafers the way a crisp cut does. If both keys behave the same way in the barrel, the wear sits inside the cylinder instead. Where no spare exists, the locksmith reads the wafers directly with a decoder, which settles the question without waiting on a second key to test it.
Servicing the cylinder in place first
The first option is always the least invasive one: cleaning out the keyway, freeing a wafer that has stuck in a raised position, and lubricating the mechanism so the existing cylinder goes back to turning the way it should. This keeps the original hardware on the vehicle and avoids cutting a new key altogether when the fault turns out to be wear or contamination rather than a broken part. Only when this fails to restore normal behaviour does the barrel come out of the column.
A key that runs through every position smoothly
The visit ends with the ignition cycling cleanly from off through accessory, on and start, and back again, with the steering lock engaging and releasing as it should. The locksmith walks through this with you, the engine started and shut off more than once, so you see for yourself that the barrel is answering the key properly and consistently before anyone drives away from the property.
Ignition Lock Repair
In the van
Pick and tension tools
Ignition lock cylinder
Cylinder decoder
Steering column trim tools
Trim clips and fasteners

Ignition Lock Repair
What affects the quote
Vehicle make, model and column design
How the ignition assembly is built varies by vehicle, a simple housing reached with a few steps, or a column locked down with shear bolts and trim that has to come off carefully. That difference in access shapes how much time the repair takes.
Evidence of an earlier forced attempt
A lock that shows signs of having already been forced needs a full cylinder and housing replacement rather than a simple service, since the internal parts can no longer be trusted as they stand.
A key broken off inside the barrel
Extracting a snapped key fragment adds its own step before any other work can begin, and the cylinder is then checked for the wear that likely caused the break in the first place.
What to have ready
- Are any warning or immobilizer lights showing on the dash?
- What is the vehicle's year, make and model?
- Where is the vehicle parked right now?
Ignition Lock Repair: questions
QuestionsWhat if there are scratches or damage around my ignition slot already?
That is noted honestly before any work begins, since it often means an earlier attempt was made on the lock. Damage like this usually points toward a full cylinder and housing replacement rather than a simple service, because the internal parts of a lock that has already been forced are rarely trustworthy afterward. You are shown what was found before deciding how to proceed together.
My car is older and uses a plain metal key. Can the ignition still be repaired?
Yes, older mechanical ignitions are generally straightforward to service, since there is no transponder chip or immobilizer layer to work around. Worn wafers, a tired spring, or a housing that has loosened over the years are addressed directly, and a fresh key is cut from the current pinning or the vehicle's key code once the barrel itself has been sorted out.
Is my vehicle's security system disabled while this work is happening?
No part of the vehicle's electronic security system is bypassed or defeated as part of a mechanical ignition repair. The locksmith works on the physical cylinder and its housing, and any question involving the immobilizer or transponder system is identified and referred rather than worked around, so the vehicle's built-in protection stays exactly as it was designed to work.
Related services

- Car Key ReplacementThe engine cranks, catches for a second and dies, and a small key-shaped light keeps blinking on the dash.
- Spare Car Key DuplicationA lockout last month ended with a locksmith opening the door and going home, and the same single key has been carried ever since with nothing behind it.
- Key Fob ProgrammingA cracked case or a spin through the wash left the fob unresponsive, and opening it up reveals a slightly corroded board where the buttons used to sit.